ONE CHANNEL THROTTLE CONTROL

The one channel throttle control will drive one or two motors proportionally forward or reverse up to 2 amps for 4.8 volts. This proportional throttle will control the throttle for forward/reverse proportional control. Throttle circuit weight is 1 gram with a total weight of 6 grams for the circuit , connectors, on/off switch and cover. Designed for 3 or 4 cell battery operation from 3.0 to 5.4 volt using N20 or similar motor. Typical application is used on an indoor blimp as a helicopter tail motor controller.

• A 4 cell nicad battery pack powers the motors, the radio, and the servos -- no additional batteries are needed
• High frequency (2 khz) PWM high efficiency circuit for 99% transfer of power to the motors
• Power conservation software allows minuscule current draw with motors off or coasting
• Repeatable throttle and dead band performance even as battery voltage drops

THREE CHANNEL THROTTLE CONTROL

The three channel throttle control will drive three motors proportionally forward or reverse up to 1 amp for 4.8 volts. Throttle circuit weight is 6 grams with a total weight of 10 grams for the circuit , connectors, on/off switch and battery holder. Designed for one 3 volt Lithium cell or 4 cell Nicad battery operation from 2.8 to 5.4 volt and N20 or similar motors.
Typical application: Used on a 4 or 5 foot indoor blimp with 3 motors. Full 3 axis control is possible without any servos.
Specify the 3 volt Lithium version complete with battery holder or the 4 cell Nicad version with battery plug.

• A 3 volt Lithium or a 4 cell nicad battery pack powers the motors, the radio, and the servos -- no additional batteries are needed.
• High frequency (2 khz) PWM high efficiency circuit for 99% transfer of power to the motors
• Power conservation software allows minuscule current draw with motors off or coasting
• Repeatable throttle and dead band performance even as battery voltage drops

SIDE CAR MIXING CIRCUIT

The circuit solders on to the bottom of a receiver and provides mixed outputs. The side car version allows access to the non-mixed connections as well as the new mixed outputs. The throttle circuit weight is 1 gram with a total weight of 2 to 4 grams for the circuit and connectors. Designed for 4 cell battery operation from 4.5 to 5.4 volt. Typical application is use on an RC Airplane for mixing receiver channels as V-tail mixing or elevon mixing. Other applications include use on indoor blimps for mixing throttle control and aileron functions as differential thrust of a dual motor blimp drive. This circuit allows low cost mixing options when expensive mixing transmitters are not available.
Specify type of mixing desired and the brand of receiver it will be used with. Also, specify wires and plugs for inputs or side car solder-on option.

• Repeatable performance even as battery voltage drops

Item #14047

$14.95

Blimp Radio Equipment -- Futaba Skysport 4 channel transmitter with an Alpex receiver, 2 ultra micro servos, 350 Mah 4-cell battery pack, and charger.

Item #1497

$175.95

BLIMP - Hitec FOCUS 3

Hitec three channel AM proportional system with HAS-03MB AM receiver with built in mixing, 1 ultra micro servo, 350 Mah 4-cell battery pack, and recharger. The transmitter uses 8 AA Alkaline batteries.

Item #1498

$69.95

ULTRA MICRO SERVO:

Specifications:

Weight: .32 ounces (9 grams)
Size: .94 x .43 x .83 in
Speed: 0.11 sec/60 deg
Torque: 11.11 oz-in
Universal Connector

Item #1480

$27.95

ULTRA ULTRA MICRO SERVO:

Specifications:

Weight: 5.7gram
Size: .90 x .37 x .61 in
Speed: 0.09 sec/60 deg
Torque: 11 oz-in
Universal Connector

Item #1482

$29.95

ULTRA MICRO MOTOR:

Designed for use with ultra miniature blimps 1' - 4' in length. Provides 1/8 ounce thrust at 4.8 volts with 2.5 inch propeller. Motor weight is 2.7 grams. Typical current draw is 100 ma.

Item #1495

$9.95

1/4 OUNCE MOTOR WITH 3" BLACK PLASTIC PROPELLER

This motor will generate 1/4 to 1/2 ounce of thrust with its 3" black plastic propeller. Designed to work on blimps that are 4-5 feet in length with proportional and computerized throttle controls. Typical current draw is 1 amp at 4.8 volts.

Item #1500

$15.95

1/3 OUNCE MOTOR & GEAR BOX WITH 6" PROPELLER:

This motor and gear box will generate ½ to 1 oz. of thrust with its 6" plastic propeller. Designed to work on blimps that are 6-8 feet in length with proportional and computerized throttle controls. Typical current draw is 1 amp at 4.8 volts.

Item #1550	Motor, Propeller & Gear Box	$21.95
Item #1552	Motor Only	$10.95

1/2 OUNCE MOTOR FOR 3 1/2 TO 4 1/2 INCH PROPELLER

This motor will provide 1/2 to 1 1/2 ounce of thrust for blimps and small airplanes on 4 to 9 cells.

Item #1561

Motor

$5.95

PROPELLERS:

High quality - high performance plastic propellers. Intended for direct drive use.